Teknomer 600 2K Polyurethane-Bitumen Based

Product description
It is a bitumen-polyurethane based, two component, fast curing liquid membrane material. It forms a highly elastic film by adhering strongly to almost all kinds of surfaces.

Usage areas
• It is used as an insulation material against moisture, pressureless and pressurized water in the waterproofing of foundations, curtain walls, terrace roofs, balconies, parking lots, bridge tops and similar areas of all buildings.
• It is applied as a waterproofing material in wet volume insulation, in the insulation of areas where plant root resistance is required, in the renovations of old waterproofing coatings.

Features and Advantages
• It gives high performance on wide terraces and deep foundations.
• Forms a seamless, super elastic insulation layer.
• It can easily solve complex details with its comfortable application consistency.
• Provides excellent adherence even on difficult surfaces.
• It shows high resistance against water ponding and freezing.
• Resistant to detergents, oil, sea water and household chemicals.

Application Instructions
The surfaces must be clean, smooth, solid, free from all kinds of dust, oil, dirt, rust, mold oil, detergent, etc. If there is segregation in the concrete, damaged and loose parts should be discarded and weak pieces should be removed. If there are cracks or cavities on the floor or wall where the application will be made, they should be repaired with appropriate TEKNOREP repair mortars. TEKNOMER 600 2K application should be started after 3-4 days.

If there is dilatation of the structure before TEKNOMER 600 2K application, first of all, the dilatation must be insulated using TEKNOMER PAH TAPES and TEKNOMER 400 D. Later, the insulation of dilatations is more difficult and costly. All drains and gutters, strainers should be insulated using chamfer tapes.

The surface to be insulated must be dry. If there is a puddle or ponding, it should be removed. As a primer on the concrete surface, two-component, epoxy-based TEKNOBOND 300 should be applied with a brush or roller at a rate of 0.20 - 0.40 kg/m2. Primer consumption varies according to the quality and absorbency of the concrete. It should be ensured that the primer is completely cured and hardened. Minimum 4 hours, maximum 48 hours should be waited for waterproofing to be done on it.

TEKNOMER 600 2K is first mixed with component A in a clean container free of all kinds of non-adhesive substances or in its own container, and component B is added to it. It is mixed with a low speed mixer until a homogeneous mixture without lumps is obtained. Mixing time should be at least 3 minutes.

The product, which has been mixed and ready for application, is applied to the surface with a stiff bristle brush or spraying machines. After the material completes its reaction, the second layer is applied in the vertical direction of the first layer application. Waiting time between coats is at least 5 hours. After the application of the first layer, when there is no trace on the fingers in the manual control, other layers can be passed. If desired, carrier glass fiber can be used as reinforcement between floors.

Application Notes / Limitations
• Since the product has no UV resistance, heat insulation boards, protection boards, geotextile felt, etc. must be applied after the application. should be covered with
• After the application, it should be protected against adverse weather conditions such as direct sunlight, strong wind, high air temperature (over +35°C), rain and frost. Before the product is fully cured, hands should be cleaned with water and detergent.
• Equipment should be cleaned with TEKNO THINNER right after the application, before it hardens. After the product hardens, it should be cleaned by mechanical methods.
• The application surface humidity should not be more than 5%.
• Foreign materials should not be added.
• The two components should only be mixed well with a mechanical mixer. During product mixing, care should be taken to ensure that there are no unmixed product components on the edges and bottoms of the packaging.
• It should be applied in two layers.
• It should not be applied in the rain.
• The product should not be diluted, it is ready to use.
• Rain, etc., until the newly applied material completes its hardening. must be protected against weather conditions.